1 | <html><head><title>Commands in /geometry/test/</title></head> |
---|
2 | <body bgcolor="#ffffff"><h2>/geometry/test/</h2><p> |
---|
3 | Geometry verification control setup.<br> |
---|
4 | Helps in detecting possible overlapping regions.<br> |
---|
5 | <p><hr><p> |
---|
6 | <h2>Sub-directories : </h2><dl> |
---|
7 | </dl><p><hr><p> |
---|
8 | <h2>Commands : </h2><dl> |
---|
9 | <p><br><p><dt><b>tolerance [<i>Tolerance</i>] [<i>Unit</i>]</b> |
---|
10 | <p><dd> |
---|
11 | Set error tolerance value.<br> |
---|
12 | Default: 1E-4*mm.<br> |
---|
13 | <p><dd>Available at all Geant4 states. |
---|
14 | <p><dd>Parameters<table border=1> |
---|
15 | <tr><td>Tolerance |
---|
16 | <td>type d |
---|
17 | <td>Omittable : current value is used as the default value. |
---|
18 | <td><tr><td>Unit |
---|
19 | <td>type s |
---|
20 | <td>Omittable : default value = mm |
---|
21 | <td>Parameter candidates : pc km m cm mm mum nm Ang fm parsec kilometer meter centimeter millimeter micrometer nanometer angstrom fermi |
---|
22 | </table> |
---|
23 | <p><br><p><dt><b>position [<i>X</i>] [<i>Y</i>] [<i>Z</i>] [<i>Unit</i>]</b> |
---|
24 | <p><dd> |
---|
25 | Set starting position.<br> |
---|
26 | <p><dd>Available at all Geant4 states. |
---|
27 | <p><dd>Parameters<table border=1> |
---|
28 | <tr><td>X |
---|
29 | <td>type d |
---|
30 | <td>Omittable : current value is used as the default value. |
---|
31 | <td><tr><td>Y |
---|
32 | <td>type d |
---|
33 | <td>Omittable : current value is used as the default value. |
---|
34 | <td><tr><td>Z |
---|
35 | <td>type d |
---|
36 | <td>Omittable : current value is used as the default value. |
---|
37 | <td><tr><td>Unit |
---|
38 | <td>type s |
---|
39 | <td>Omittable : default value = cm |
---|
40 | <td>Parameter candidates : pc km m cm mm mum nm Ang fm parsec kilometer meter centimeter millimeter micrometer nanometer angstrom fermi |
---|
41 | </table> |
---|
42 | <p><br><p><dt><b>direction [<i>Px</i>] [<i>Py</i>] [<i>Pz</i>] [<i>Unit</i>]</b> |
---|
43 | <p><dd> |
---|
44 | Set momentum direction.<br> |
---|
45 | Direction needs not to be a unit vector.<br> |
---|
46 | <p><dd>Range : Px != 0 || Py != 0 || Pz != 0 |
---|
47 | <p><dd>Available at all Geant4 states. |
---|
48 | <p><dd>Parameters<table border=1> |
---|
49 | <tr><td>Px |
---|
50 | <td>type d |
---|
51 | <td>Omittable : current value is used as the default value. |
---|
52 | <td><tr><td>Py |
---|
53 | <td>type d |
---|
54 | <td>Omittable : current value is used as the default value. |
---|
55 | <td><tr><td>Pz |
---|
56 | <td>type d |
---|
57 | <td>Omittable : current value is used as the default value. |
---|
58 | <td><tr><td>Unit |
---|
59 | <td>type s |
---|
60 | <td><td></table> |
---|
61 | <p><br><p><dt><b>line_test</b> |
---|
62 | <p><dd> |
---|
63 | Performs test along a single specified direction/position.<br> |
---|
64 | Use position and direction commands to change default.<br> |
---|
65 | Default: position(0,0,0), direction(0,0,1).<br> |
---|
66 | <p><dd>Available Geant4 state(s) : Idle |
---|
67 | <p><br><p><dt><b>grid_test</b> |
---|
68 | <p><dd> |
---|
69 | Start running the default grid test.<br> |
---|
70 | A grid of lines parallel to a cartesian axis is used;<br> |
---|
71 | Only direct daughters of the mother volumes are checked.<br> |
---|
72 | <p><dd>Available Geant4 state(s) : Idle |
---|
73 | <p><br><p><dt><b>recursive_test</b> |
---|
74 | <p><dd> |
---|
75 | Start running the recursive grid test.<br> |
---|
76 | A grid of lines along a cartesian axis is recursively<br> |
---|
77 | to all daughters and daughters of daughters, etc.<br> |
---|
78 | WARNING: it may take a very long time, depending on geometry complexity !<br> |
---|
79 | <p><dd>Available Geant4 state(s) : Idle |
---|
80 | <p><br><p><dt><b>cylinder_test</b> |
---|
81 | <p><dd> |
---|
82 | Start running the cylinder test.<br> |
---|
83 | A set of lines in a cylindrical pattern of gradually<br> |
---|
84 | increasing mesh size.<br> |
---|
85 | <p><dd>Available Geant4 state(s) : Idle |
---|
86 | <p><br><p><dt><b>run</b> |
---|
87 | <p><dd> |
---|
88 | Start running the default grid test.<br> |
---|
89 | Same as the grid_test command.<br> |
---|
90 | <p><dd>Available Geant4 state(s) : Idle |
---|
91 | </dl></body></html> |
---|