[904] | 1 | <html><head><title>Commands in /geometry/test/</title></head> |
---|
| 2 | <body bgcolor="#ffffff"><h2>/geometry/test/</h2><p> |
---|
| 3 | Geometry verification control setup.<br> |
---|
| 4 | Helps in detecting possible overlapping regions.<br> |
---|
| 5 | <p><hr><p> |
---|
| 6 | <h2>Sub-directories : </h2><dl> |
---|
| 7 | </dl><p><hr><p> |
---|
| 8 | <h2>Commands : </h2><dl> |
---|
| 9 | <p><br><p><dt><b>tolerance [<i>Tolerance</i>] [<i>Unit</i>]</b> |
---|
| 10 | <p><dd> |
---|
| 11 | Set error tolerance value.<br> |
---|
| 12 | Default: 1E-4*mm.<br> |
---|
| 13 | <p><dd>Available at all Geant4 states. |
---|
| 14 | <p><dd>Parameters<table border=1> |
---|
| 15 | <tr><td>Tolerance |
---|
| 16 | <td>type d |
---|
| 17 | <td>Omittable : current value is used as the default value. |
---|
| 18 | <td><tr><td>Unit |
---|
| 19 | <td>type s |
---|
| 20 | <td>Omittable : default value = mm |
---|
| 21 | <td>Parameter candidates : pc km m cm mm mum nm Ang fm parsec kilometer meter centimeter millimeter micrometer nanometer angstrom fermi |
---|
| 22 | </table> |
---|
| 23 | <p><br><p><dt><b>position [<i>X</i>] [<i>Y</i>] [<i>Z</i>] [<i>Unit</i>]</b> |
---|
| 24 | <p><dd> |
---|
| 25 | Set starting position.<br> |
---|
| 26 | <p><dd>Available at all Geant4 states. |
---|
| 27 | <p><dd>Parameters<table border=1> |
---|
| 28 | <tr><td>X |
---|
| 29 | <td>type d |
---|
| 30 | <td>Omittable : current value is used as the default value. |
---|
| 31 | <td><tr><td>Y |
---|
| 32 | <td>type d |
---|
| 33 | <td>Omittable : current value is used as the default value. |
---|
| 34 | <td><tr><td>Z |
---|
| 35 | <td>type d |
---|
| 36 | <td>Omittable : current value is used as the default value. |
---|
| 37 | <td><tr><td>Unit |
---|
| 38 | <td>type s |
---|
| 39 | <td>Omittable : default value = cm |
---|
| 40 | <td>Parameter candidates : pc km m cm mm mum nm Ang fm parsec kilometer meter centimeter millimeter micrometer nanometer angstrom fermi |
---|
| 41 | </table> |
---|
| 42 | <p><br><p><dt><b>direction [<i>Px</i>] [<i>Py</i>] [<i>Pz</i>] [<i>Unit</i>]</b> |
---|
| 43 | <p><dd> |
---|
| 44 | Set momentum direction.<br> |
---|
| 45 | Direction needs not to be a unit vector.<br> |
---|
| 46 | <p><dd>Range : Px != 0 || Py != 0 || Pz != 0 |
---|
| 47 | <p><dd>Available at all Geant4 states. |
---|
| 48 | <p><dd>Parameters<table border=1> |
---|
| 49 | <tr><td>Px |
---|
| 50 | <td>type d |
---|
| 51 | <td>Omittable : current value is used as the default value. |
---|
| 52 | <td><tr><td>Py |
---|
| 53 | <td>type d |
---|
| 54 | <td>Omittable : current value is used as the default value. |
---|
| 55 | <td><tr><td>Pz |
---|
| 56 | <td>type d |
---|
| 57 | <td>Omittable : current value is used as the default value. |
---|
| 58 | <td><tr><td>Unit |
---|
| 59 | <td>type s |
---|
| 60 | <td><td></table> |
---|
| 61 | <p><br><p><dt><b>line_test</b> |
---|
| 62 | <p><dd> |
---|
| 63 | Performs test along a single specified direction/position.<br> |
---|
| 64 | Use position and direction commands to change default.<br> |
---|
| 65 | Default: position(0,0,0), direction(0,0,1).<br> |
---|
| 66 | <p><dd>Available Geant4 state(s) : Idle |
---|
| 67 | <p><br><p><dt><b>grid_test</b> |
---|
| 68 | <p><dd> |
---|
| 69 | Start running the default grid test.<br> |
---|
| 70 | A grid of lines parallel to a cartesian axis is used;<br> |
---|
| 71 | Only direct daughters of the mother volumes are checked.<br> |
---|
| 72 | <p><dd>Available Geant4 state(s) : Idle |
---|
| 73 | <p><br><p><dt><b>recursive_test</b> |
---|
| 74 | <p><dd> |
---|
| 75 | Start running the recursive grid test.<br> |
---|
| 76 | A grid of lines along a cartesian axis is recursively<br> |
---|
| 77 | to all daughters and daughters of daughters, etc.<br> |
---|
| 78 | WARNING: it may take a very long time, depending on geometry complexity !<br> |
---|
| 79 | <p><dd>Available Geant4 state(s) : Idle |
---|
| 80 | <p><br><p><dt><b>cylinder_test</b> |
---|
| 81 | <p><dd> |
---|
| 82 | Start running the cylinder test.<br> |
---|
| 83 | A set of lines in a cylindrical pattern of gradually<br> |
---|
| 84 | increasing mesh size.<br> |
---|
| 85 | <p><dd>Available Geant4 state(s) : Idle |
---|
| 86 | <p><br><p><dt><b>run</b> |
---|
| 87 | <p><dd> |
---|
| 88 | Start running the default grid test.<br> |
---|
| 89 | Same as the grid_test command.<br> |
---|
| 90 | <p><dd>Available Geant4 state(s) : Idle |
---|
| 91 | </dl></body></html> |
---|